| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: add hook transactions for device deletions
Restore the flag that indicates that the hook is going away, ie.
NFT_HOOK_REMOVE, but add a new transaction object to track deletion
of hooks without altering the basechain/flowtable hook_list during
the preparation phase.
The existing approach that moves the hook from the basechain/flowtable
hook_list to transaction hook_list breaks netlink dump path readers
of this RCU-protected list.
It should be possible use an array for nft_trans_hook to store the
deleted hooks to compact the representation but I am not expecting
many hook object, specially now that wildcard support for devices
is in place.
Note that the nft_trans_chain_hooks() list contains a list of struct
nft_trans_hook objects for DELCHAIN and DELFLOWTABLE commands, while
this list stores struct nft_hook objects for NEWCHAIN and NEWFLOWTABLE.
Note that new commands can be updated to use nft_trans_hook for
consistency.
This patch also adapts the event notification path to deal with the list
of hook transactions. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: udp: Create exceptions before socket matching
Currently, when ICMP Fragmentation Needed and Redirect Message packets
are locally delivered and quote a UDP packet, a FIB nexthop exception
(FNHE) is only created if the kernel can match the UDP packet to an
existing socket.
This behavior allows off-path attackers to conduct a side-channel attack
on the FNHE cache in order to discover the ephemeral port used by a
connected UDP socket.
Commit 6457378fe796 ("ipv4: use siphash instead of Jenkins in
fnhe_hashfun()") and commit 67d6d681e15b ("ipv4: make exception cache
less predictible") tried to mitigate such attacks by making it harder
for attackers to discover hash collisions in the FNHE cache and by
randomizing the number of exceptions a hash bucket can hold,
respectively. Unfortunately, both of the mitigations can be bypassed.
Instead, mitigate such attacks by always creating a FNHE, even before
trying to find a matching socket. Do that by calling ipv4_update_pmtu()
and ipv4_redirect(), the helpers used when the quoted packet did not
originate from a socket.
This means that guesses (right or wrong) from an off-path attacker will
always result in a FNHE being created or updated in the cache that the
attacker can observe.
Pass an oif of 0, in a similar fashion to icmp_err(). This is also the
oif used by the socket path for sockets that are not bound to a device.
Note that this does not allow attackers to create FNHEs that they could
not create before, as both helpers can already be reached with little to
no validation. For example, by sending an ICMP error that quotes an ICMP
Echo Reply or one that quotes a UDP source port that matches a wildcard
socket.
Also note that in the good case (matched socket) the above scheme comes
at the cost of an extra route lookup, as the no socket helpers perform
their own lookup before the one performed by ipv4_sk_update_pmtu() /
ipv4_sk_redirect(). When the two resolve to different nexthops, it also
results in two exceptions being created for the same destination IP. One
in the FNHE cache of the nexthop resolved by the no socket helpers and
another in the FNHE cache of the nexthop used by the socket. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/ttm: fix swapped-out resources never leaving their bulk_move range
ttm_tt_swapout() returns the number of pages swapped out on success and
a negative error code on failure; for a populated ttm it never returns
zero. Commit b2ed01e7ad3d ("drm/ttm: Fix ttm_bo_swapout() infinite LRU
walk on swapout failure") moved the bulk_move bookkeeping in
ttm_bo_swapout_cb() under "if (!ret)", so the
ttm_resource_del_bulk_move_unevictable() / ttm_resource_move_to_lru_tail()
pair is now skipped on every successful swapout. The equivalent change
for the shrinker in commit 1d59f36e95f7 ("drm/ttm: Fix ttm_bo_shrink()
infinite LRU walk on backup failure") tests "lret > 0", which is what
was intended here as well.
Before b2ed01e7ad3d the resource was taken off the bulk_move before the
swapout; since then a swapped-out resource stays inside its BO's
bulk_move range (and on the manager LRU) although it is unevictable.
When it is later freed or the BO leaves the bulk_move
(ttm_resource_free(), ttm_bo_set_bulk_move() via amdgpu_vm_bo_del()),
ttm_resource_del_bulk_move() skips it because of its
!ttm_resource_unevictable() guard, so a range endpoint in pos->first /
pos->last is left pointing at freed memory. The next
ttm_lru_bulk_move_tail() or ttm_resource_add_bulk_move() on that cursor
is a use-after-free, seen as the resv WARN in ttm_lru_bulk_move_add(),
"list_del corruption" in ttm_resource_move_to_lru_tail() or a NULL
dereference in ttm_resource_manager_next() -- minutes to hours after a
hibernation, or at process exit / reboot following one. Samuel
Ainsworth's analysis of drm/amd issue 5387 (see Link) identified the
dangling cursor; the missing removal at swapout time is the reason it
dangles.
Testing the condition for success restores the removal. On an AMD
Phoenix APU (ASUS UM3406GA, gfx1103) running suspend-then-hibernate on
a 7.0.y stable kernel carrying the backport (Ubuntu 7.0.0-31) the bug
crashed 5 of 18 hibernation cycles; a function profile of one
hibernation showed 336 ttm_tt_swapout() calls and zero
ttm_resource_del_bulk_move_unevictable() calls. With this change the
removal happens for every swapped-out resource and 12 further cycles
were clean. |
| In the Linux kernel, the following vulnerability has been resolved:
regcache: Do not overwrite error code when finalizing cache after error
During regcache initialization, if an error occurs in the
cache_ops->populate callback, and if cache operations include an exit
callback, the error code from populate() is overwritten with the return
value from exit(). This hides the error condition from the caller of
regcache_init(), and can cause NULL pointer dereferences when the regcache
is later accessed. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: ctxfi: Don't enumerate SPDIF1 at DAIO initialization
The recent refactoring of xfi driver changed the assignment of
atc->daios[] at atc_get_resources(); now it loops over all enum
DAIOTYP entries while it looped formerly only a part of them.
The problem is that the last entry, SPDIF1, is a special type that
is used only for hw20k1 CTSB073X model (as a replacement of SPDIFIO),
and there is no corresponding definition for hw20k2. Due to the lack
of the info, it caused a kernel crash on hw20k2, which was already
worked around by the commit b045ab3dff97 ("ALSA: ctxfi: Fix missing
SPDIFI1 index handling").
This patch addresses the root cause of the regression above properly,
simply by skipping the incorrect SPDIF1 type in the parser loop.
For making the change clearer, the code is slightly arranged, too. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix crash in ethtool offline loopback test
Since the conversion of ice to page pool, the ethtool loopback test
crashes:
BUG: kernel NULL pointer dereference, address: 000000000000000c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 1100f1067 P4D 0
Oops: Oops: 0002 [#1] SMP NOPTI
CPU: 23 UID: 0 PID: 5904 Comm: ethtool Kdump: loaded Not tainted 6.19.0-0.rc7.260128g1f97d9dcf5364.49.eln154.x86_64 #1 PREEMPT(lazy)
Hardware name: [...]
RIP: 0010:ice_alloc_rx_bufs+0x1cd/0x310 [ice]
Code: 83 6c 24 30 01 66 41 89 47 08 0f 84 c0 00 00 00 41 0f b7 dc 48 8b 44 24 18 48 c1 e3 04 41 bb 00 10 00 00 48 8d 2c 18 8b 04 24 <89> 45 0c 41 8b 4d 00 49 d3 e3 44 3b 5c 24 24 0f 83 ac fe ff ff 44
RSP: 0018:ff7894738aa1f768 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000700 RDI: 0000000000000000
RBP: 0000000000000000 R08: ff16dcae79880200 R09: 0000000000000019
R10: 0000000000000001 R11: 0000000000001000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: ff16dcae6c670000
FS: 00007fcf428850c0(0000) GS:ff16dcb149710000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000000c CR3: 0000000121227005 CR4: 0000000000773ef0
PKRU: 55555554
Call Trace:
<TASK>
ice_vsi_cfg_rxq+0xca/0x460 [ice]
ice_vsi_cfg_rxqs+0x54/0x70 [ice]
ice_loopback_test+0xa9/0x520 [ice]
ice_self_test+0x1b9/0x280 [ice]
ethtool_self_test+0xe5/0x200
__dev_ethtool+0x1106/0x1a90
dev_ethtool+0xbe/0x1a0
dev_ioctl+0x258/0x4c0
sock_do_ioctl+0xe3/0x130
__x64_sys_ioctl+0xb9/0x100
do_syscall_64+0x7c/0x700
entry_SYSCALL_64_after_hwframe+0x76/0x7e
[...]
It crashes because we have not initialized libeth for the rx ring.
Fix it by treating ICE_VSI_LB VSIs slightly more like normal PF VSIs and
letting them have a q_vector. It's just a dummy, because the loopback
test does not use interrupts, but it contains a napi struct that can be
passed to libeth_rx_fq_create() called from ice_vsi_cfg_rxq() ->
ice_rxq_pp_create(). |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: fix ntfs_mount_options leak in ntfs_fill_super()
In ntfs_fill_super(), the fc->fs_private pointer is set to NULL without
first freeing the memory it points to. This causes the subsequent call to
ntfs_fs_free() to skip freeing the ntfs_mount_options structure.
This results in a kmemleak report:
unreferenced object 0xff1100015378b800 (size 32):
comm "mount", pid 582, jiffies 4294890685
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 ed ff ed ff 00 04 00 00 ................
backtrace (crc ed541d8c):
__kmalloc_cache_noprof+0x424/0x5a0
__ntfs_init_fs_context+0x47/0x590
alloc_fs_context+0x5d8/0x960
__x64_sys_fsopen+0xb1/0x190
do_syscall_64+0x50/0x1f0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
This issue can be reproduced using the following commands:
fallocate -l 100M test.file
mount test.file /tmp/test
Since sbi->options is duplicated from fc->fs_private and does not
directly use the memory allocated for fs_private, it is unnecessary to
set fc->fs_private to NULL.
Additionally, this patch simplifies the code by utilizing the helper
function put_mount_options() instead of open-coding the cleanup logic. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/CPU/AMD: Fix AMD TLBI Erratum #1718
The processor may fail to invalidate a TLB entry while executing an
INVLPGB/TLBSYNC instruction pair.
Detect the erratum and apply a software workaround when a microcode fix
is not present. |
| In the Linux kernel, the following vulnerability has been resolved:
dm-integrity: fix buffer overflow in inline mode with large tag size
In inline mode, dm_integrity_check and dm_integrity_inline_recheck
compute the checksum of each block into an on-stack buffer of
HASH_MAX_DIGESTSIZE bytes. integrity_sector_checksum pads its result
with zeroes up to the tag size, so if the tag size is larger than
HASH_MAX_DIGESTSIZE, the padding runs past the end of the buffer. With
CONFIG_STACKPROTECTOR the kernel panics in dm_integrity_check on the
first read.
Enlarge both buffers to hold MAX_TAG_SIZE bytes, as commit b93b6643e9b5
("dm integrity: fix a crash with unusually large tag size") did for
integrity_metadata.
Note that this is not a security bug because the buffer overflow can only
be triggered by root. |
| In the Linux kernel, the following vulnerability has been resolved:
tee: shm: reject zero-sized allocations in tee_dyn_shm_alloc_helper()
tee_dyn_shm_alloc_helper() derives nr_pages from a caller-supplied size
and passes it to alloc_pages_exact() without checking it. For size == 0
nr_pages is 0, and alloc_pages_exact(0) calls get_order(0), which is
documented as undefined and returns BITS_PER_LONG - PAGE_SHIFT. The page
allocator then trips its order > MAX_PAGE_ORDER warning and fails the
allocation; on a panic_on_warn kernel that ends the boot.
This can be triggered by TEE_IOC_SHM_ALLOC with struct
tee_ioctl_shm_alloc_data where size is 0.
Reject a zero page count, as register_shm_helper() already does for the
register path. |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/register: don't exempt disabled rings from task restrictions
A ring created with IORING_SETUP_R_DISABLED is exempt from its register
restrictions until it is enabled. This lets the creator register the
restrictions and then enable the ring with IORING_REGISTER_ENABLE_RINGS,
whether or not that opcode is in the allowed set.
Since commit ed82f35b926b ("io_uring: allow registration of per-task
restrictions"), a ring also inherits restrictions from the task that
creates it, and the same exemption applies to those. A task whose
register opcodes are restricted can therefore create a disabled ring,
issue any register opcode on it, and then enable it.
Mark rings whose restrictions were inherited from the task, and keep
checking register opcodes for them while the ring is disabled. Enabling
such a ring now requires IORING_REGISTER_ENABLE_RINGS to be in the
task's allowed set. Per-ring restrictions registered on a disabled ring
work as before.
[axboe: amend with inheritance flag fixup] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: drain the hangcheck timer and works on V3D unbind
Nothing stops the hangcheck timer that submitted jobs arm, or the
job_done_work that the render-done interrupt queues, at teardown:
vc4_irq_disable() cancels only overflow_mem_work, and vc4_gem_destroy()
runs from the drm-managed release, after vc4_v3d_unbind() has already
uninstalled the V3D interrupt and cleared vc4->v3d. A timer still armed
by then reads V3D registers through the NULL vc4->v3d pointer, and the
late callbacks run on the vc4_dev embedding them after it has been
freed.
Drain them in vc4_v3d_unbind(): shut the timer down and cancel
reset_work before the interrupt is taken down, because its
vc4_irq_reset() re-enables it, then flush job_done_work so that
completions queued at teardown still release their jobs.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel_pcie: fix TX descriptor bounds check
btintel_pcie_prepare_tx() uses tfd_index to access the TFD and data
buffer arrays before the index is advanced modulo txq->count. An index
equal to txq->count is one past the end of both arrays, so reject it in
the bounds check. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: don't schedule deferred kernel page table freeing while booting
Booting with a boot-time function tracer and a filter, for example
ftrace=function ftrace_filter=pud_free_pmd_page
panics on 7.3-rc4 as soon as the tracer starts:
[ 23.531178] Starting tracer 'function'
[ 23.675800] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000038: 0000 [#1] SMP KASAN NOPTI
[ 23.819917] KASAN: null-ptr-deref in range [0x00000000000001c0-0x00000000000001c7]
[ 23.964025] CPU: 0 UID: 0 PID: 0 Comm: swapper Not tainted 7.3.0-rc4-fe2ec83746e5-with-fixes-v2+ #195 PREEMPT(undef)
[ 24.252248] RIP: 0010:__queue_work+0xab/0xf00
[ 25.981629] Call Trace:
[ 26.125727] <TASK>
[ 26.413912] ? pagetable_free_kernel+0x20/0x120
[ 26.990283] queue_work_on+0x97/0xf0
[ 27.134382] __cpa_collapse_large_pages+0x501/0x6f0
[ 27.566662] cpa_flush+0x394/0x620
[ 27.998953] change_page_attr_set_clr+0x321/0x4a0
[ 29.151729] set_memory_rox+0xa2/0xf0
[ 29.584018] create_trampoline+0x431/0x6f0
...
[ 44.343347] Kernel panic - not syncing: Attempted to kill the idle task!
The boot-time tracer is started from early_trace_init(), which runs
before workqueue_init_early(). Making its trampoline read-only splits a
large page, and CPA collapses it again right away. The split table has
been a kernel page table since commit 9e4a3ec3411b
("x86/mm/pat: Allocate split page tables as kernel page tables"), so the
collapse frees it through pagetable_free_kernel(), which queues work on
system_percpu_wq - still NULL at that point. That commit is correct in
itself; it only lets CPA reach pagetable_free_kernel() before the
workqueue that function relies on exists.
Keep putting the table on the list, but don't schedule the work while
the system is still booting. A core_initcall schedules it once to free
whatever was queued by then. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: patch: fix handling of bpf-jit execmem addresses
Commit 8718e5a3090b ("riscv: patch: skip fixmap mapping when kernel text
is already writable") gated the core_kernel_text() branch of patch_map()
on CONFIG_STRICT_KERNEL_RWX, and explicitly left the vmalloc branch
unchanged. That branch has a separate problem.
That branch only creates a temporary writable fixmap alias when
CONFIG_STRICT_MODULE_RWX is enabled, and otherwise assumes the target is
directly writable and returns the address unchanged. That assumption no
longer holds: bpf_prog_pack_alloc calls set_memory_rox() on every pack
unconditionally in alloc_new_pack(), independently of any
CONFIG_STRICT_*_RWX option, so BPF text in the vmalloc area is read-only
regardless of what CONFIG_STRICT_MODULE_RWX says.
With CONFIG_STRICT_MODULE_RWX=n, patch_map() returns the read-only
address directly, the subsequent copy_to_kernel_nofault() takes a
page fault and returns -EFAULT. bpf_arch_text_copy() turns that into
-EINVAL, which propagates through bpf_jit_binary_pack_finalize() to the
WARN_ON() in bpf_int_jit_compile() and leaves the program un-JITed.
Note that BPF cannot be fixed the way kprobes was in
commit bdc46e507b59 ("riscv: mm: make EXECMEM_KPROBES writable without
CONFIG_STRICT_MODULE_RWX"). EXECMEM_BPF is already PAGE_KERNEL, i.e.
writable at allocation time; the read-only mapping is established
afterwards by generic code in alloc_new_pack(), which arch code cannot
influence. The only place this can be handled is patch_map().
This is the same problem that was fixed on arm64 by commit b1480ed230ac
("arm64: patching: fix handling of execmem addresses"), and the fix is
the same: CONFIG_EXECMEM is what actually tracks whether the vmalloc
area can hold executable memory that needs a temporary alias to be
written. CONFIG_BPF_JIT, CONFIG_KPROBES and CONFIG_MODULES all select
it.
Note that this is not limited to CONFIG_MODULES=n. Unlike arm64, riscv
selects CONFIG_ARCH_OPTIONAL_KERNEL_RWX, so CONFIG_STRICT_MODULE_RWX can
be disabled with CONFIG_MODULES=y as well, and the bug is reachable in
that configuration too.
The !CONFIG_MMU build is unaffected: it has its own __patch_insn_set()
and __patch_insn_write() implementations and never calls patch_map(). |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: Fix status of pending commands flushed on power off
cmd_complete_rsp() receives a struct cmd_lookup and, for a pending
command that has no cmd_complete callback, falls through to
cmd_status_rsp(cmd, data). cmd_status_rsp() reads data as a u8 *, so
the status sent comes from the first byte of match->sk's
representation, not from match->mgmt_status.
commit f53e1c9c726d ("Bluetooth: MGMT: Fix possible crash on
mgmt_index_removed") changed the callers' data from &status to &match
and updated the cmd_complete branch to match->mgmt_status, but left
the fall-through passing data unchanged.
In mgmt_index_removed() match->sk is NULL, so every such command is
answered with status 0x00 (Success) instead of
MGMT_STATUS_INVALID_INDEX. In __mgmt_power_off() it is NULL too,
unless a Set Powered command was pending: then settings_rsp() has
stored that command's socket in match->sk, and the byte sent comes
from the socket pointer. Either way the status the caller set,
MGMT_STATUS_NOT_POWERED (or MGMT_STATUS_INVALID_INDEX when the device
is being unregistered), is lost.
Pass the status the callers set.
This was seen on a QCA9377 laptop: bluetoothd's Start Discovery,
pending when the adapter was powered off, was answered with Command
Status 0x00 and no parameters, and bluetoothd 5.72 crashed on the
zero-length success. BlueZ master has since added the length check
on that path ("adapter: Fix crash on short start discovery reply",
BlueZ a734b06059cb), but userspace should still be told Not Powered,
not Success.
Tested on Ubuntu 7.0.0-31 with a virtual controller (hci_vhci):
power off is held in HCI Write Scan Enable while a Start Discovery is
submitted, and the flush answers it with status 0x00 before this
change and 0x0f (Not Powered) after. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: serialize vblank counter reads against GPU reset
The vblank counter callback reads display registers and scanout
position without holding reset_domain->sem. During GPU recovery,
display commit work can call the callback while reset owns the
semaphore for writing. The hardware access then triggers the
lockdep_assert_held() in amdgpu_device_skip_hw_access() and sets
TAINT_WARN when lockdep is enabled.
Try to acquire the reset semaphore for reading before accessing the
hardware, and hold it across the counter and scanout-position reads.
If reset is already in progress, return DRM's cached software vblank
count instead. This avoids blocking behind reset and avoids accessing
display hardware while it is being reset.
The cached count is less accurate than the hardware count, but is
used only when reset prevents a safe hardware read. This addresses
the reset-time warning from this vblank path; it does not suppress or
fix unrelated lockdep warnings.
(cherry picked from commit 51a4359f7431a4be5e42803c8bdaf7e0e5be2934) |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: samsung: i2s: enable op_clk in probe to balance runtime PM
The probe function puts the device into the runtime PM active state with
only the "iis" bus clock enabled, but it also sets priv->op_clk to the
parent of the RCLK_SRC mux without enabling it. The runtime PM suspend
callback disables both clocks, so the first runtime suspend after probe
disables op_clk once more than it was enabled.
On Exynos5250 Arndale both clocks resolve to the same EXYNOS_I2S_BUS gate,
so this triggers the following warning during boot:
WARNING: drivers/clk/clk.c:1270 at clk_core_disable+0xe4/0x23c, CPU#0: kworker/u8:3/45
i2s_bus already disabled
...
Workqueue: pm pm_runtime_work
Call trace:
...
clk_core_disable from clk_disable+0x28/0x34
clk_disable from i2s_runtime_suspend+0x58/0x68 [snd_soc_i2s]
i2s_runtime_suspend [snd_soc_i2s] from genpd_runtime_suspend+0xc4/0x298
genpd_runtime_suspend from __rpm_callback+0x48/0x18c
__rpm_callback from rpm_callback+0x4c/0x50
rpm_callback from rpm_suspend+0xf4/0x718
rpm_suspend from pm_runtime_work+0x9c/0xa0
...
Fix this by enabling op_clk in probe right after getting it, so the clock
state matches the runtime PM active state, and by disabling it in remove. |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: validate transport header presence in set_ipv6_addr
When executing IPv6 address rewrite actions on IPv6 fragments,
set_ipv6_addr() calls update_ipv6_checksum(). If parse_ipv6hdr()
processes a non-first IPv6 fragment, it sets key->ip.proto to
NEXTHDR_FRAGMENT and returns early without calling
skb_set_transport_header().
update_ipv6_checksum() unconditionally evaluates skb_transport_offset()
on entry before checking l4_proto. Because skb->transport_header is
uninitialized, this triggers a warning under CONFIG_DEBUG_NET=y although
it is completely harmless.
Fix this by returning early in update_ipv6_checksum() if l4_proto is
NEXTHDR_FRAGMENT. This avoids reading the uninitialized transport offset
for fragments while preserving the debug warning for any other protocol
where the transport header is unexpectedly missing.
See the syzbot trace:
!skb_transport_header_was_set(skb)
WARNING: ./include/linux/skbuff.h:3075 at skb_transport_header include/linux/skbuff.h:3075 [inline], CPU#1: syz-executor463/5635
WARNING: ./include/linux/skbuff.h:3075 at skb_transport_offset include/linux/skbuff.h:3250 [inline], CPU#1: syz-executor463/5635
WARNING: ./include/linux/skbuff.h:3075 at update_ipv6_checksum net/openvswitch/actions.c:361 [inline], CPU#1: syz-executor463/5635
WARNING: ./include/linux/skbuff.h:3075 at set_ipv6_addr+0x462/0x660 net/openvswitch/actions.c:399, CPU#1: syz-executor463/5635
[...]
RIP: 0010:skb_transport_header include/linux/skbuff.h:3075 [inline]
RIP: 0010:skb_transport_offset include/linux/skbuff.h:3250 [inline]
RIP: 0010:update_ipv6_checksum net/openvswitch/actions.c:361 [inline]
RIP: 0010:set_ipv6_addr+0x462/0x660 net/openvswitch/actions.c:399
[...]
Call Trace:
<TASK>
set_ipv6 net/openvswitch/actions.c:531 [inline]
do_execute_actions+0x557e/0x8600 net/openvswitch/actions.c:1366
ovs_execute_actions+0xde/0x520 net/openvswitch/actions.c:1592
ovs_packet_cmd_execute+0xb4f/0xf10 net/openvswitch/datapath.c:705
genl_family_rcv_msg_doit+0x233/0x340 net/netlink/genetlink.c:1114
genl_rcv_msg+0x614/0x7a0 net/netlink/genetlink.c:1209
netlink_rcv_skb+0x226/0x4a0 net/netlink/af_netlink.c:2572
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1218
netlink_unicast+0x7bd/0x940 net/netlink/af_netlink.c:1361
netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1916
sock_sendmsg_nosec+0x14e/0x190 net/socket.c:800 |
